Command Start CS-580i FM Installationsanleitung

Stöbern Sie online oder laden Sie Installationsanleitung nach Fernbedingungen Command Start CS-580i FM herunter. Command Start CS-580i FM Installation guide Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 22
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
AUTOMATIC TRANSMISSION REMOTE STARTER
COMBO WITH FULL ALARM SYSTEM
CS-580
i
FM
Installation Guide
A note concerning the battery inside the transmitter:
Depending on the usage of the transmitter, the battery can last anywhere between 3 to 6
months. When the battery is low, it the transmitter will emit two beeps in a repetitive
cycle. At that point you should replace your battery with a new one. That is why we
recommend that you keep a spare battery somewhere handy such as the glove
compartment.
Notice
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of
the product, be that either damage to the vehicle itself or to the Unit. This Unit must be installed by a certified
technician using all safety devices supplied. Please note that this guide has been written for properly trained
Autostart technicians: a certain level of skills and knowledge is therefore assumed. Please review the
Installation Guide carefully before beginning any work.
Warning
This System is designed for vehicles with an automatic Transmission only. Before installing the Unit,
test that the vehicle does not start when the Gear Select Lever is in the “Drive” position. If it starts in gear,
install a manual-transmission remote starter system instead.
DOC:.1.00 September 17, 2004 Gp CA Lp Manufactured in Canada
Seitenansicht 0
1 2 3 4 5 6 ... 21 22

Inhaltsverzeichnis

Seite 1 - Installation Guide

AUTOMATIC TRANSMISSION REMOTE STARTER COMBO WITH FULL ALARM SYSTEM CS-580i FM Installation Guide A note concerning the battery inside the transmitte

Seite 2 - Table of Contents

P. 10 Installation Guide The System must exit Valet Mode before a Transmitter Programming procedure can be carried out: Getting out of Valet Mode 1

Seite 3 - Included in the Kit

Installation Guide P. 11 Once you access a particular programming Mode, you will automatically start at Function 1. Once you select one of the Optio

Seite 4 - GROUND OUT WHEN RUNNING wire

P. 12 Installation Guide MODE 2 * INDICATES DEFAULT SETTING FUNCTION 1 – Home Valet TM OPTION 1 Home Valet ENABLED OPTION 2* Home Valet DISABL

Seite 5 - Harness Description

Installation Guide P. 13 OPTION 2* Shock Sense MONITORED / Warn-away MONITORED OPTION 3 Shock Sense MONITORED / Warn-away IGNORED OPTION 4 Shock

Seite 6 - ON position

P. 14 Installation Guide Automatic Tach Programming This simple procedure can replace the Multi-speed Tach Programming procedure: 1. Make sure tha

Seite 7

Installation Guide P. 15 Testing Before putting back the vehicle together, it is recommended to check that the system operates properly. The followi

Seite 8 - Flashing the Hood Pin Switch

P. 16 Installation Guide Supplementary Information Fifth Relay Output (2nd IGN, ACC or CRANK) Systems of this series are equipped with an on-board

Seite 9 - Before you Proceed

Installation Guide P. 17 once again). Please note that most OEM systems will not rearm the Alarm while the Engine is running, but will still lock th

Seite 10 - Getting out of Valet Mode

P. 18 Installation Guide disarmed after being previously armed, the opening or closing of a Door will start a 10-sec. timer, after which the Horn o

Seite 11 - Programming Options

Installation Guide P. 19 2. Press and release the Break Pedal 6 times (within 13 seconds from entering Programming Mode). 3. The Parking Lights wi

Seite 12

P. 2 Installation Guide Table of Contents Table of Contents ...2 Introduction...

Seite 13 - Multi-speed Tach Programming

P. 20 Installation Guide Intrusion Codes through the LED Light If there has been an intrusion in the vehicle while it was locked and armed, the LED

Seite 14 - Siren or Horn Chirp Timing

Installation Guide P. 21 Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, Alarm and Starter Kill armed. • End of Run

Seite 15 - Testing

CS-580i FM Wiring Diagram CS-580i FM Installation Guide

Seite 16

Installation Guide P. 3 Introduction This Guide contains all the information relevant and necessary for the installation of the Alarm and Remote Sta

Seite 17

P. 4 Installation Guide Installation Points to Remember ♦ Make sure that vehicles equipped with an automatic Transmission do not start while in any o

Seite 18 - Resetting the System

Installation Guide P. 5 Note: The Parking Light Output Relay of the unit gives two clicking sounds for each flash of the lights: one click when th

Seite 19 - Intrusion Codes

P. 6 Installation Guide 5 YELLOW (+) 12 V Parking Light output This wire provides a +12 V output and must be connected on the vehicle to the Parki

Seite 20 - Diagnostics – Chirps Table

Installation Guide P. 7 9 PURPLE (+) Siren or Horn output +12 V Siren output. Connect to the positive side of the Siren. This wire provides a cons

Seite 21 - TRUNK button pressed

P. 8 Installation Guide power up the Ignition and Glow-plug circuits and simply wait for the time-out before starting: • Connecting the Glow-plug

Seite 22

Once the System has entered Programming Mode, you will have a selection of many different sub-menus, which will be described later in this Guide: a. T

Kommentare zu diesen Handbüchern

Keine Kommentare